* Cannot be combined with any other offer. Coupon must be presented at time of vehicle drop off. Max $100 Discount. Discount on Labor Only. One coupon per customer/vehicle
** See store for details.
Irving, TX Diesel Engine Service
In 1892 Rudolf Diesel developed and obtained the German patent for the diesel engine. His goal was to create an engine that was more efficient than the gasoline engine that was invented in 1876.
There are two main differences between a diesel engine and a gasoline engine.
- A gasoline engine intakes a mixture of gas and air, compresses it and ignites the mixture with a spark. A diesel engine takes in just air, compresses it and then injects fuel into the compressed air. The heat of the compressed air lights the fuel spontaneously.
- A gasoline engine compresses at a ratio of 8:1 to 12:1, while a diesel engine compresses at a ratio of 14:1 to as high as 25:1. The higher compression ratio of the diesel engine leads to better efficiency.
Diesel engines use direct fuel injection (DI), that is to say the diesel fuel is injected directly into the cylinder. The diesel engine has no spark plugs. The air it takes in is compressed and the fuel is injected directly into the cylinder where the heat caused by the air compression ignites the fuel. In the old days this meant that it exploded and expanded very quickly, making a noisy engine. This is why most diesel cars were IDI (indirect injection); the rough behavior was fixed by injecting the fuel into a small pre-combustion chamber that is connected to the cylinder by a narrow passage. However the newer breed of DI engines use other techniques to tame the behavior of the engine, such as two stage injection, electronic control, and acoustic shrouds and shock absorbing engine mounts to mask the rattle.
The injector on a diesel engine is its most complex component and has been the subject of a great deal of development and innovation. On any specific engine it may be located in a variety of places. The injector has to be able to withstand the temperature and pressure inside the cylinder and still deliver the fuel in a fine mist. Getting the mist circulated in the cylinder so that it is evenly distributed is also a problem, so some diesel engines employ special induction valves, pre-combustion chambers or other devices to swirl the air in the combustion chamber or otherwise improve the ignition and combustion process.
One major difference between a gas engine and a diesel engine is in the injection process. Most car engines use port injection or a carburetor rather than direct injection. In a car engine all of the fuel is loaded into the cylinder during the intake stroke and then compressed. The compression of the fuel/air mixture limits the compression ratio of the engine. If it compresses the air too much, the fuel/air mixture spontaneously ignites and causes knocking. A diesel compresses only air, so the compression ratio can be much higher. The higher the compression ratio, the more power is generated.
Glow plugs are needed. Diesel engines rely on the heat of compressed air to ignite their fuel. When the engine is cold, compression alone may not produce enough heat for the fuel to burn, so most car and truck diesels use glow plugs, electric elements that heat up the cylinder before a cold engine is started These electric heaters are switched on for anywhere from 5 to 10 seconds to make the engine easier to start. They use about 15 amps each (you have one for each cylinder). This is why you need a high amperage battery. For areas with severe winters, a block heater is a good idea. Many diesels have them as standard or optional equipment.
Diesel engines require more frequent routine maintenance than gasoline engines. More frequent oil changes generally required at 3,000 miles and more frequent fuel filter and air filter changes. On the plus side however, normal gasoline engine maintenance such as replacing the spark plugs, distributor cap and rotor and replacing ignition wires are not necessary on a diesel engine. You don’t have to worry about an Ignition module or coil going bad. It’s simply because a diesel engine has no ignition system.
Low engine compression will result in insufficient heat being generated to ignite the fuel and cause hard starting. This is more of a problem with older or high mileage vehicles. To find out the compression perform a cold engine compression test. Compression should be between 20 to 35 bars or 300 to 500 PSI. Anything below this will cause starting problems.
Low fuel pressure
It is in this area that most fuel supply problems occur. The problem could either be poor fuel supply to the rail/injectors or the rail/injectors are not holding the fuel within the system. The best way to diagnose this is to look at the fuel supply in 3 areas.
- Low pressure supply from the tank to the high pressure pump (HPP) – some vehicles rely on the HPP to suck the fuel from the tank whilst others have an electric pump in the tank or fuel line to supply fuel to the HPP. The supply from the tank to the HPP should be about 2 to 5 bars.
- Fuel is delivered from the HPP to the rail/injectors at about 200 bars during cranking, 300 bars at idle and anything from 1200 to 1800 bars running.
- Once the fuel is delivered into the rail/injectors at the relevant pressure it must be maintained within the injectors or rail.
Low cranking speed
If the engine turns over too slowly, the pump cannot generate enough fuel pressure to activate start of injection causing hard starting problems. This is usually seen more in the colder months especially if the battery is run down.
Glow plugs or relay faulty
The engine relies on the glow plugs to generate heat to help with the combustion cycle. Some engines only use the glow plugs when cold but others will allow the glow plugs to work when the ECU (vehicle’s computer) needs them to be on to help with combustion. Problems in this area will cause diesel engine starting problems, uneven running and white smoke when the engine is cold.
Insufficient fuel supply
This speaks for itself, not enough fuel in the tank or a problem with supply pipes being cracked or bent. The fuel tank breather can sometimes be blocked causing a vacuum in the tank which in turn draws the fuel back to the tank.
Fuel quality and contamination
Working with diesel injectors we see the result of poor fuel quality – damage and condition of the internal components. I know that if a good quality diesel and an additive is used regularly it will prolong the life of diesel injection equipment.
Poor fuel quality and general wear and tear are not the only cause of injector failure, the newer type of injectors sometimes fail due to design problems.
I would estimate that about 85% of injectors fail due to fuel related issues and the balance due to design problems.
Air – Vacuum in fuel supply and Blocked fuel supply
This is similar to “insufficient fuel supply” but dirty fuel filters or a faulty filter head assembly may also cause fuel supply issues and hard starting.
Probably the biggest result of injector failure is due to the injectors having excessive return flow or back leakage. This is due to worn parts which allow excessive fuel to go through the diesel injector and to return back to the tank or fuel system. This causes a drop in rail pressure (see “low fuel pressure”) which results in hard starting or not starting at all.
Another problem resulting from worn parts is a delay in the start of injection which in turn results in rough running at low RPM or your diesel not starting.
Faulty high pressure pump
If the pump is faulty there will be a “low fuel pressure” problem. This problem arises if the pump “breaks up” internally causing iron filings to get into the fuel system. Normally this causes damage to the diesel injectors and unless the complete fuel system is attended to, the problem will arise again. This is an expensive failure and no short cuts can be taken.
Faulty pressure regulator sensor
Most vehicles have a pressure regulator fitted on the high pressure pump and a sensor fitted on the rail. If either of these are faulty there will be running issues like hard starting, uneven tick over and the vehicle cutting out when the RPM is increased.
Faulty low pressure pump
Not all vehicles have a low pressure supply pump but if they do it can be found either in the tank or on the fuel pipe near the tank. If your low pressure pump is faulty, you may experience symptoms similar to those of a “faulty high pressure pump”.
Air intake restriction
This would be due to a dirty air cleaner, blocked pipes or a stuck butterfly valve found on some vehicles. In addition, a faulty air flow sensor on the air intake will cause problems running and create excessive smoke.
We are seeing more turbos failing with newer vehicles, I put it down to a combination of things, high revving engines demanding more power, incorrect driver actions(not allowing the engine to idle a while when started and before switching off), poor maintenance and not replacing old oil with a good quality oil. A turbo spins at about 42000 revolutions per minute, the average washing machine at 1000 rpm. As vehicles get older the turbo waste gate sticks causing the vehicle to either shut down, go into limp home mode or smoke excessively.
If a vehicle has a variable vane turbo, problems can arise if the vanes carbon up. The symptoms are lack of power, black smoke and hesitation on acceleration. Also make sure that all the vacuum pipes and sensors that operate the turbo are operating correctly.
Another issue that can cause similar problems is if the air pipes to and from the inlet, inter cooler and turbo, or the pipes leak due to damaged or loose clamps.
I do not know why EGR (exhaust gas recycling) valves were ever put onto diesel engines. They cause more trouble than they are worth. The idea is that whilst the engine is at tick over, a valve opens and allows some of the exhaust gases to pass back into the nice clean air intake manifold.
After a while the gases containing dirty, sooty carbons start to cover and coat the intake area and valves causing the air to fuel ratio to become unbalanced thus resulting in more black smoke being emitted from the exhaust. This black smoke is then drawn back into the air intake via the EGR valve. A vicious cycle then starts with the engine producing more smoke and sootier carbons being drawn into the intake. I would always recommend the EGR valve to be blanked off but some vehicles will not allow this.
Injector blow-by, seat leaking
Injector “blow-by” can be the cause of some of the following symptoms. Hard or difficult starting / erratic or uneven tick over or idle / lumpy running / smoke on tick over or acceleration / black tar around the injectors and a chuffing sound from the engine when running. Injector “blow-by” occurs when the injector does not seal against the injector seat in the cylinder head. Often a chuffing sound is heard or black “tar” can be seen around the injectors.
On some engine applications if this continues serious engine damage could result due to the fact that the ECU will over compensate the fuelling on the cylinder or cylinders with the seating problem causing piston washing or cylinder over fuelling. Even if the injector is removed, cleaned, a new copper washer fitted and then replaced it will not always rectify the problem. The reason for this is that the seat in the cylinder head has been eroded by the escaping combustion gases resulting in damage to the seat. The only way to reface the seat is to use a seat cutting tool and gently reface the seat in the head. .
Cam andf crank sensor
Check that the sensors are not loose, cracked or damaged as they are not very expensive. If you have any doubts I would recommend replacing them.
Injector wiring harness
More of a problem with vehicles that have the injectors under the rocker cover and allow oil to come in contact with the electrical connections. Even though some diagnostic machines will condemn the injector/s, many times the fault lies with the wiring harness.
Check that the electrical connections on the injectors are good and are making contact.
Internal engine problems
This is generally mechanical failure such as problems with bearings, pistons, oil pressure, overheating, valves and more. The list is endless and it is best to get an engine specialist to diagnose the fault.
The Answer is in the Smoke
We can generally understand what is wrong with a diesel engine by the color of smoke emitted from the exhaust. There are three basic colors – black, white and blue.
This is due to a air to fuel ratio imbalance, either the fuel system is delivering too much fuel into the engine or there is not enough clean air (oxygen ). A few things to look for :
- Faulty injectors (injectors need attention at about 100.000 to 120 000 miles)
- Faulty injector pump
- Dirty air cleaner
- Turbocharger or intercooler faulty
- Problems within cylinder head, valves clogged up due to faulty EGR (exhaust gas recycling unit)
Normally means that the fuel injected into the cylinder is not burning correctly. The smoke will burn your eyes.
- Engine/pump timing out
- Fuel starvation to the pump causing the pump timing not to operate correctly
- Low engine compression
- Water/petrol in the fuel
The engine is burning engine oil
- Worn cylinders or piston rings
- Faulty valves or valve stem seals
- Engine over full with engine oil
- Faulty injector pump/lift pump allowing engine oil to be mixed with the diesel